Egg Lovers/Owners

Air Bag Solution for the rear........no welding necessary........I was seriously looking at this........but found another option.  Another plus........it Fabulous.

[url]http://www.upgarage.com/upgarage/stock/stock.php?stocklist_detail=1&data_kubun=2&shouhin_cd=0809161001075&tenpo_id=161[/url]

Keep in mind that you will still need bags for the front, compressor, tank, lines, etc.

Sukoshiyoshi

Kool...

So, it uses the strut as the air bag. NEAT!!

From the looks of the kit you keep the springs too. With that in mind, I dont know if you are able to go super low? 

Any pictures of it installed available?

You know, you can modify the brackets so that you wont have to weld them...just bolt them in.

Please elaborate on how you would "bolt" up without "welding"?  

Sukoshiyoshi

this might be good.. i just gashed a big hole in my bag yesterday nite.. it sux.. gotta go to get it fixed...

Hey Yoshi,

Let me try to see if I can try this out haha...sorry if I am using weird terms to explain the stuff.

If you check our suspension rods on the rear the bottom part has a hole on the "cup" thingy.
[IMG]http://i3.photobucket.com/albums/y73/cleaverv/air%20suspension/DSC07538.jpg[/IMG]

What you can do is put a bolt long enough (offset) and hold the "bracket" down.

As for the top, you can also make a bracket by putting a bolt through the "bracket" and it will grab on to that "inner" cup that is part of the car.
[IMG]http://i3.photobucket.com/albums/y73/cleaverv/air%20suspension/DSC07539.jpg[/IMG]

I have yet to try it out, but I will try it too because I myself dont want to weld the brackets eventhough its pretty easy to do so.

I hope it makes sense! haha....sorry if it dont yoshi!

[QUOTE=esvipstyle;188063]this might be good.. i just gashed a big hole in my bag yesterday nite.. it sux.. gotta go to get it fixed...[/QUOTE]

how'd you do that??

[QUOTE=shawnthemonster;188072]how'd you do that??[/QUOTE]

i guess when the car was dropped onna slope.. the bag dropped crooked.. and then when i pumped it up.. it got snagged on summin back there and gashed it..

Hondaboi.......very interesting concept........please post up when you do you air set up.

esvipstyle,

Do you have any photos of how much "clearance" you got between the bags and the wheel?  That is one thing that I am very worried about when it comes to going with UAS Bags.  The Easystreet set up does not "bulge outward" quite as much as the UAS Bags which will allow for a lot more clearance.

Sukoshiyoshi

i dont think its rubbing on the wheel.. i think its rubbing on one of the ball joints..

[QUOTE=hondaboi;188066]Hey Yoshi,


If you check our suspension rods on the rear the bottom part has a hole on the "cup" thingy.
[IMG]http://i3.photobucket.com/albums/y73/cleaverv/air%20suspension/DSC07538.jpg[/IMG]

[/QUOTE]

u see that joint where its holding down the sway bar or whatever.. its rubbing on that thing!

yoshi...
 
that rear set up look similar to the Xbs.. I custom made my own mounts that dont require any welding.. looks like the egg can do the same.. 
 
the UAS bags are not as wide as the Firestones.. 
 
here is my theory.. if it dotn work make it work.. when there a will theres a way.. 
 
are you still looking for a kit.. Co the guy with the Black Cherry XB that i just did his bags has a used UAS kit sitting at his house.. IM pretty sure it can work on your car.. just have to fabricate..

Marshall......PM sent!  The "possible" no welding is "music to my ears".  

Just wish that I could keep my TEINs ("for sale")and make them work some how.........naturally out of all the "Coil-Over" Kits out there.......the only one UAS Bags don't slide over is TEINs.

Sukoshiyoshi

hey yoshi,

i just wanted to let you know that the "concept" that I have was helped by UAS. I showed him some pics and he said its possible to do it without welding which is a good thing.

I believe that you will have air before I do...I dont have the money at the moment! haha

Canover Air Setup
[URL]http://page.auctions.yahoo.co.jp/jp/auction/113203413[/URL]

There was an ACC/Air Runner setup going for ~$500 USD but can't find it anymore.

Wilson from PG Motoring USA can get you this. [email]wilson@pgmotoringusa.com[/email]

yoshi... why are you scared to weld... ?

For me, its not that im scared. Its just if you do need to replace the bag or service, its just a hassle to cut the weld an reweld it again, where as if it was bolted, then you would just need to unbolt it. 

Thats all..:)

[quote=sukoshiyoshi;188191]Marshall......PM sent! The "possible" no welding is "music to my ears". 
 
Just wish that I could keep my TEINs ("for sale")and make them work some how.........naturally out of all the "Coil-Over" Kits out there.......the only one UAS Bags don't slide over is TEINs.
 
Sukoshiyoshi[/quote]
 
 
did mines all bolt up.. ill just use the same set up.. 
 
the UAS bags dont also fit the tein XB coil overs..

Marshall,

Can you get me pricing on how much your friend would be willing to let his used sitting around UAS System for?

Shawn,

Not really scared of Welding as I have a Master Welder who has already offer his services........it is all about when I got to do some "upgrades" or some R&R..........no Welding is going to work out best in the long run.  After cutting up the Egg (Fenders/Sliding Door) I am all about doing "Custom" work.....actually I should say I am all about having my Master Techs do Custom work on the Egg.  LOL

Sukoshiyoshi

very nice. check these out. came across them looking for a setup. pretty tempting

[url]http://www.dsengineering.co.uk/airsuspensionkits.php?model=78[/url]

Yoshi,
Looks like the rear shocks on the pics are for the TCR 11/21 IRS.  The shocks both have "stems" top & bottom compared to the Previa which has an "eye" on top and stem on the bottom.  Check out mdenoga's posted pic for comparison.

^^^^good catch.........another reason I am happy I decided not to get these.......it does say TCR10 just for the record.

Sukoshiyoshi