time for new wheels ...need help with fitment

alright folks i'm looking for a new set of work wheels most likely these
[url]http://www.workwheelsusa.com/product.php?category=23&wheel=48[/url]
schwert sc1

i would like proper flush fitment ...as of now my rims are nicely tuck but very minimum camber .....so anyone with the right offset , rim size and tire size and i can place a order thanx

what it looks like now
[IMG]http://i54.tinypic.com/2vmhi8g.jpg[/IMG]

what i want to look like

[IMG]http://i52.tinypic.com/2larcwm.jpg[/IMG]

do some research and look up "right offset , rim size and tire size" for your ride instead of relying on others to do that for you

check out [url]http://rimtuck.com/[/url] 
maybe that will help you

there is a flushed out white gs430 I have seen but havent seen him post in a while

VIPDOUT.....i think i message him before no answer....

Miucus......i already did a bunch of search. i can order rims that will fit my car perfect to oem spec but thats not what i am looking for.i didnt find much info that i need for the fitment i want...i-forge, forgestar and other high end rim companies don't give out offset ..and this is a VIP car  forum where we share info , thats why i was wondering if anyone with a 3GS that has proper fitment would like to share...also rimtuck.com sucks..couldn't find shit on there useless like your reply!!!!!!

planning on doing some fender work?  or just camber mods?

Here's a pic I took of my teammate's car.  

[IMG]http://i85.photobucket.com/albums/k76/moog177/Tommy/6beada50.jpg[/IMG]

20x9.5 +0
20x11 +6

Fenders had to be pulled pretty good in the rear to fit and slight in the front.

[IMG]http://i85.photobucket.com/albums/k76/moog177/Tommy/9600e324.jpg[/IMG]

^^^I'm loving this 3GS!

[QUOTE=waijai;354023]Here's a pic I took of my teammate's car.  

[IMG]http://i85.photobucket.com/albums/k76/moog177/Tommy/6beada50.jpg[/IMG]

20x9.5 +0
20x11 +6

Fenders had to be pulled pretty good in the rear to fit and slight in the front.[/QUOTE]

Nice!

[QUOTE=waijai;354023]
[IMG]http://i85.photobucket.com/albums/k76/moog177/Tommy/6beada50.jpg[/IMG]

[/QUOTE]

Oh my!  that GS is so sick!  Right click>Save.

i still remember these wheels when i first open it after it land from jpn.

[QUOTE=REV-01;380999]i still remember these wheels when i first open it after it land from jpn.[/QUOTE]

Strange reminiscing of wheels you've brought in before anyhow..haha.  Special connection with this set Samson?

[QUOTE=elpresidente;381004]Strange reminiscing of wheels you've brought in before anyhow..haha.  Special connection with this set Samson?[/QUOTE]

yeah i remember it was the first set where we start playing with arms.

I have figured out the max offset I can go before I need a fender pull, my fenders are shaved completely flat as possible inside to allow the rim to tuck. My rear clears by 1mm super close and that is 20x10.5 +26 and the front is perfectly flush at my ride height at 20x9 +12 but could go +10 before needing a pull. VIPNISS from my calculations has pulled his fenders 1 inch in the rear and about 2/3 of an inch in the front. If you are trying to ride low and not pull fenders than those specs are money. But if you want to put in work go for it but be careful with pulling the rear too much cause you ll end up losing the integrity of the rear bumper bracket and have a bumper that flaps in the wind. Good luck, BTW did you ever get the headrest out???

I'm running a 20x10f and 20x11r with a 0 offset all around.
shaved rear fenders rolled fronts...
here it is with about -8 camber in the rear...still need to fab front arms to add camber to the front... 2nd pic should give you an idea of the fitment.. good luck!

[IMG]http://i20.photobucket.com/albums/b209/ryanbeez/10.jpg[/IMG]