roll hard

What do you do when your engine is 3" under the subframe?
raise it.

[url=http://www.flickr.com/photos/yokotas13/5650235110/][img]http://farm6.static.flickr.com/5141/5650235110_f6c52a4a51_b.jpg[/img][/url]
[url=http://www.flickr.com/photos/yokotas13/5650235110/]IMG_0667[/url] by [url=http://www.flickr.com/people/yokotas13/]Flsimages[/url], on Flickr
do work boys and girls!

That's a thick block you got there Grant :biggthumpup:
What car is that from?

i'm considering this for my q. did you run into any other clearance issues with the drivtrain? is this the original engine or a swap motor?

even with original engine id have clearance problems

as it sits now
[url=http://www.flickr.com/photos/yokotas13/5657409165/][img]http://farm6.static.flickr.com/5108/5657409165_4e2e1ed304_b.jpg[/img][/url]
[url=http://www.flickr.com/photos/yokotas13/5657409165/]IMG_9862[/url] by [url=http://www.flickr.com/people/yokotas13/]Flsimages[/url], on Flickr
[url=http://www.flickr.com/photos/yokotas13/5657981222/][img]http://farm6.static.flickr.com/5023/5657981222_3b9374bb37_b.jpg[/img][/url]
[url=http://www.flickr.com/photos/yokotas13/5657981222/]IMG_9857[/url] by [url=http://www.flickr.com/people/yokotas13/]Flsimages[/url], on Flickr
[url=http://www.flickr.com/photos/yokotas13/5657400019/][img]http://farm6.static.flickr.com/5061/5657400019_ba38e57c90_b.jpg[/img][/url]
[url=http://www.flickr.com/photos/yokotas13/5657400019/]IMG_9848[/url] by [url=http://www.flickr.com/people/yokotas13/]Flsimages[/url], on Flickr
[url=http://www.flickr.com/photos/yokotas13/5657395799/][img]http://farm6.static.flickr.com/5222/5657395799_d9c6ebc0a2_b.jpg[/img][/url]
[url=http://www.flickr.com/photos/yokotas13/5657395799/]IMG_9844[/url] by [url=http://www.flickr.com/people/yokotas13/]Flsimages[/url], on Flickr

what's wrong with your camera...out of focus :innoutrofl2:

lensbaby bro!

messin with ya Grant.  I wanna see full pics of the miata

haha. certain forums get sneak peaks. VSC isnt one lulz

boooo

dont boo me. im not the reason haha

302 powered..i gotta see that man.

[url=http://www.flickr.com/photos/yokotas13/5657972004/][img]http://farm6.static.flickr.com/5027/5657972004_999f1437b7_b.jpg[/img][/url]
[url=http://www.flickr.com/photos/yokotas13/5657972004/]IMG_9846[/url] by [url=http://www.flickr.com/people/yokotas13/]Flsimages[/url], on Flickr
lol

[QUOTE=FLSImages;384123]even with original engine id have clearance problems[/QUOTE]

that wasn't really where i was going with that question. what i was wondering is if you had more room to raise the motor because of the swapped motor/tranny. 3" seems like a lot, especially in the tunnel. did you have to clearance any areas under the car to get it that high?

i had to cut out the whole tranny tunnel and reweld it back in and part of the firewall.

word... too much work for me right now, but i really only need .5-1". i'll see what it looks like when i replace the tranny.

its not my DD, its my race car, so it doesnt really matter lol. i have to wire it still and plumb it, so not in a huge rush

not my daily either but i'm not looking to go in that hard yet. hopin to get this beast on the road soon. i'm thinkin i can get .5" with no issues which will match the .5" my rear subframe will  be raised.

yeah, i wa able to hit an inch without problems. but anything more than that was a PITA with the miata and the 302 drivetrain...so had to chop cut rebuild

do work son.

i wish i was cool enough to see the full pics... :innoutrofl2: