Odyssey fitment ?

Okay I have two questions pertaining to the RA1 chassis (95-98 Odyssey)

1.) I searched, but came up with nothing. Can I really fit 9" wide wheels up front and 10" wide in the rear with little to no pulling or rolling? 

2.) Besdies air is there any springs or coilovers for my soon to be project?

18x9 -10, 18x10 +11, just trust me

(actually, don't but wouldn't that look badass?!)

Now, if my memory is not on the pipe, I believe Aragosta makes coilovers for the RA1.
Without looking I'd bet JIC has made a set as well, they have some for just about everything.

Just go 9" up front with maybe low disk and 9" out back with super low disk  :)
 
But anyhow, RASRX7 has done 9.5" upfront and 10" out back, but he had to pull and roll the rear.

Guys I appreciate the help...no one local to turn to!!

you'd be pretty surprised with the potential of those odysseys
unlike other honda cars, they can take pretty good sizings.

without rolling the fenders though, you are pretty limited like every other car out there.

currently at my situation, from just being lowered, i can fit 9 up front and 10 in the back easily.
now all you have to do is determine what offset you can go with it

So you saying you can put a 10 inch wide wheel on the rear of an Odyssey?I'd like to see that and I want lip on the rear also.

[QUOTE=BigMone;94953]So you saying you can put a 10 inch wide wheel on the rear of an Odyssey?I'd like to see that and I want lip on the rear also.[/QUOTE]

I had a set of 18x10 +44 on the rears ,but the tires were 265/35/18, that I borrowed from a friend of mines for testing.

wheels on his car:

[IMG]http://img.photobucket.com/albums/v156/rayz_garage/toys/Picture026.jpg[/IMG]

wheels on my van:

[IMG]http://img.photobucket.com/albums/v156/rayz_garage/toys/vanwithwheels011.jpg[/IMG]

[IMG]http://img.photobucket.com/albums/v156/rayz_garage/toys/vanwithwheels022.jpg[/IMG]

[IMG]http://img.photobucket.com/albums/v156/rayz_garage/toys/vanwithwheels025.jpg[/IMG]

I decided not to get them due to the amount they "poked" out..(yes I know, they are mounted on backwards)


I now have 18x8.5 +38 all around on my RA1..I added 12mm spacers all around  with minimal rubbing with a full load..If you roll the back a little, they would fit fine with no problems.

I'm pretty sure you can fit 10's but you'll have to stretch the hell out of the tires and chamber that thing in alot..And you cant really load up the van or it'll rub.

Look in the box/van section..I think chicago RA1(?) has 10's in the rear.

So like I thought no 10s in the rear...

[quote=BigMone;95624]So like I thought no 10s in the rear...[/quote]
i got 10.5 on back of mine b4...this might help.. since theres only like 4 or 5 of us...
 
[IMG]http://www.superstar-wheel.com/products/leonhardiritt/images/bugel/bugel_11c.jpg[/IMG]
 
SIZE：F 1990 +36　R 1995 +40
 
[IMG]http://www.superstar-wheel.com/products/leonhardiritt/images/bugel/bugel_24c.jpg[/IMG]
 
SIZE：F 1990 +7　R 19100 +33
 
The car body needs to be lowered down.A camber kit is installed.The size of each rear wheel exceeds the applied rim width
 
[IMG]http://www.superstar-wheel.com/products/leonhardiritt/images/bugel/bugel_25c.jpg[/IMG]
 
SIZE：F 1995 -8　R 19120 -53
 
The car body needs to be lowered down.The front rear fender is blistered

19s or go home! 

even though tech126's rims stuck out a mile , those look like they would be propperly flush with about +3 inches of drop and 4-6degrees of camber. That is the same way my rear 1910+24s would look if I bolted them up on a stock height ra1. But with camber and drop they will be flush no problem. Also remember the tires on those rims shown above is about 40mm EXTRA of what should be run on the back.  the typical tire sizes for the RA1 I see being used is 215/35F and 225/35R. I don't know what the tire sizes are for 18s..but you don't need to know that because its 19s all day!

[IMG]http://i39.photobucket.com/albums/e179/rasrx76/oasis/Photo0163.jpg[/IMG]
215/35/19 225/35/19 falken fk452.... x9 and x10 
[URL="http://i39.photobucket.com/albums/e179/rasrx76/oasis/Photo0163.jpg"][/URL]

although im not familiar with honda fitments, it looks to me like you should even be able to fit a 10" in the front. it you see the first two van pics, the difference between the two front widths is about an inch, so you should be able to get a 10" up front. thats probably no pulling, just rolling. but again, im not familiar with hondas fitments, but offering what i see.
Charley